How to Repair Computer - Dead Display

Hello everyone, how come, this time I will give tips to improve and maximize your computer's performance, for the first time you have to prepare some tools for the purposes of these tips and tricks.

The tool that you have to prepare is in the form of a screwdriver, pliers, rubber eraser, and some additional parts that you can use to provide additional performance, with that tool you can disassemble and remove some parts to repair errors from your computer.



After all the tools have been prepared, don't forget to pray and prepare a few snacks to support your mood booster, one more prepare cleaning tools such as wipes to clean the computer from dust and dirt, of course the computer is very dusty if so long not cleaned. 

Now you can open the casing lid on the cpu, usually there are two bolts or slot slots that you have to take off to open them, after you take them off, take the PSU cable off and then we release the PSU.

Because basically, a computer that does not appear image is the main factor is dust that has accumulated inside the CPU casing, so some parts must be removed from the CPU cpu, remove the motherboard, and ram on the motherboard, either VGA card or Sound Card attached to the PCI slot available on the motherboard unit.

From some cases, all of them lead to the most common things are dust, corrosion, weak windows and virus operating windows, which makes the performance on the computer of course very disturbed, from here it all starts in the increase in heat temperature on the cpu, cpu usage is always 100%, heatsink is noisy and there are many more cases that I have handled.

The next step after all the parts have been removed from the CPU cpu, then now the cleaning process on the kesing first, this session is the easiest and easiest session, so you have to actually do this session, you better be tired than you will facing computer errors again, yes even though the error must be on a computer system or device on the computer.


After clean it, of course you will definitely do the assembly, now in the assembly session you must clean the parts you have removed, in the form of a motherboard, hdd, ram, ram slot, PCI slot, VGA card and Sound Card or Lan Card that you install on a computer.

Ram Cleaning Process :

How to clean the ram is by rubbing the rubber eraser on the yellow iron which then goes into the ram slot.


Processor Cleaning Process

How to clean the processor part is indeed quite easy, but need to remember caution needs to be done, that every processor type varies on the type and brand.

Clean the processor with a tissue or dry cloth to remove the old processor paste, as well as the treatment of iron heatsinks that stick to the processor.

Then clean the processor fan from dust using a dry brush that can reach between the heats.

Then clean the processor fan from the dust using a dry brush that can reach between the heats, do the same thing on the motherboard, once again be careful in carrying out this cleaning process, because this is an important part of a computer.

After everything is finished, then the next session is a personal computer assembly session, do the installation first of the backpanel contained in the removable case, the installation of the mouse and keyboard are two ports that cannot be separated, of course, right and left, meaning this section is usually at the top of the matherboard or in the backpanel position.

Don't forget to eat the snacks that you prepared earlier, be careful if you leave them alone, hahhahahaha

After everything is assembled and installed, don't first close it on the cpu cover, because this process has not been completely finished, because there is still a possibility that occurs in this cpu cleaning.

Do not forget to reattach the cables that you have removed before to then reinstall now, make sure all cables are installed properly, look back on what has been installed firmly, then reinstall the RAM that was released for the process of gluing, and re-installed in a good and correct position as before, to install it you can just match the center line in the ram slot, so that there is no misplacement or loosening in the installation, because there can be a conclusion on that part.

don't forget to install the heatsink cable that was removed to do the cleaning process, on the heatsink cable there is a special slot that is very easy to install, just you see and it is definitely installed, match the socket frame to the cable slot.


Okay it's time to reactivate the computer that you have installed, the installation process is correct and the cleaning is correct, the process is all confirmed to be restarted in case the display turns off, and congratulations your computer can be used again.


But keep in mind that this process can of course not always always be good, in fact every personal computer has other characteristics that you may not understand, in most cases after the dust-cleaning process that has been done, new problems always arise, the most common being computers the image is still not showing, this is caused by the weak current in the PSU that delivers electricity to supply current on the motherboard.


If you haven't also displayed an image on a computer monitor screen :

For something like this maybe I can still help with the special treatment on the computer, maybe you can try removing the VGA card on a motherboard to reduce the load of excess current that is supplied on the weak PSU, or other parts that can be removed to reduce the load the electricity, after all this has been done is definitely able and successfully resolved.


End of article 

Maybe this is all I can share with you in other countries besides Indonesia, with this small and simple tutorial can help you to maintain or maintain your own computer device.

See you in other interesting articles, don't forget to share, and comment on this article if you like it, say like it, if you don't like it, don't like it, because every response I will always receive is to build a good image for my blog, thanks.




_lastyoungboy_

How to Repair Computer - Dead Display

How to Repair Computer - Dead Display

Hello everyone, how come, this time I will give tips to improve and maximize your computer's performance, for the first time you have to prepare some tools for the purposes of these tips and tricks.

The tool that you have to prepare is in the form of a screwdriver, pliers, rubber eraser, and some additional parts that you can use to provide additional performance, with that tool you can disassemble and remove some parts to repair errors from your computer.



After all the tools have been prepared, don't forget to pray and prepare a few snacks to support your mood booster, one more prepare cleaning tools such as wipes to clean the computer from dust and dirt, of course the computer is very dusty if so long not cleaned. 

Now you can open the casing lid on the cpu, usually there are two bolts or slot slots that you have to take off to open them, after you take them off, take the PSU cable off and then we release the PSU.

Because basically, a computer that does not appear image is the main factor is dust that has accumulated inside the CPU casing, so some parts must be removed from the CPU cpu, remove the motherboard, and ram on the motherboard, either VGA card or Sound Card attached to the PCI slot available on the motherboard unit.

From some cases, all of them lead to the most common things are dust, corrosion, weak windows and virus operating windows, which makes the performance on the computer of course very disturbed, from here it all starts in the increase in heat temperature on the cpu, cpu usage is always 100%, heatsink is noisy and there are many more cases that I have handled.

The next step after all the parts have been removed from the CPU cpu, then now the cleaning process on the kesing first, this session is the easiest and easiest session, so you have to actually do this session, you better be tired than you will facing computer errors again, yes even though the error must be on a computer system or device on the computer.


After clean it, of course you will definitely do the assembly, now in the assembly session you must clean the parts you have removed, in the form of a motherboard, hdd, ram, ram slot, PCI slot, VGA card and Sound Card or Lan Card that you install on a computer.

Ram Cleaning Process :

How to clean the ram is by rubbing the rubber eraser on the yellow iron which then goes into the ram slot.


Processor Cleaning Process

How to clean the processor part is indeed quite easy, but need to remember caution needs to be done, that every processor type varies on the type and brand.

Clean the processor with a tissue or dry cloth to remove the old processor paste, as well as the treatment of iron heatsinks that stick to the processor.

Then clean the processor fan from dust using a dry brush that can reach between the heats.

Then clean the processor fan from the dust using a dry brush that can reach between the heats, do the same thing on the motherboard, once again be careful in carrying out this cleaning process, because this is an important part of a computer.

After everything is finished, then the next session is a personal computer assembly session, do the installation first of the backpanel contained in the removable case, the installation of the mouse and keyboard are two ports that cannot be separated, of course, right and left, meaning this section is usually at the top of the matherboard or in the backpanel position.

Don't forget to eat the snacks that you prepared earlier, be careful if you leave them alone, hahhahahaha

After everything is assembled and installed, don't first close it on the cpu cover, because this process has not been completely finished, because there is still a possibility that occurs in this cpu cleaning.

Do not forget to reattach the cables that you have removed before to then reinstall now, make sure all cables are installed properly, look back on what has been installed firmly, then reinstall the RAM that was released for the process of gluing, and re-installed in a good and correct position as before, to install it you can just match the center line in the ram slot, so that there is no misplacement or loosening in the installation, because there can be a conclusion on that part.

don't forget to install the heatsink cable that was removed to do the cleaning process, on the heatsink cable there is a special slot that is very easy to install, just you see and it is definitely installed, match the socket frame to the cable slot.


Okay it's time to reactivate the computer that you have installed, the installation process is correct and the cleaning is correct, the process is all confirmed to be restarted in case the display turns off, and congratulations your computer can be used again.


But keep in mind that this process can of course not always always be good, in fact every personal computer has other characteristics that you may not understand, in most cases after the dust-cleaning process that has been done, new problems always arise, the most common being computers the image is still not showing, this is caused by the weak current in the PSU that delivers electricity to supply current on the motherboard.


If you haven't also displayed an image on a computer monitor screen :

For something like this maybe I can still help with the special treatment on the computer, maybe you can try removing the VGA card on a motherboard to reduce the load of excess current that is supplied on the weak PSU, or other parts that can be removed to reduce the load the electricity, after all this has been done is definitely able and successfully resolved.


End of article 

Maybe this is all I can share with you in other countries besides Indonesia, with this small and simple tutorial can help you to maintain or maintain your own computer device.

See you in other interesting articles, don't forget to share, and comment on this article if you like it, say like it, if you don't like it, don't like it, because every response I will always receive is to build a good image for my blog, thanks.




_lastyoungboy_

Tidak ada komentar: